- Manuals
- Brands
- Kapsys Manuals
- Telephone
- MiniVision 2
- Quick start manual
Advertisem*nt
Table of Contents
-
Overview
See AlsoMiniVision2 Cell Phone - Easy-to-Use Cell Phone for Vision Loss | Shop | RAZ MobilityRAZ Mobility MiniVision2 Mobile Phone for Users with Visual ImpairmentsMiniVision2: A Simple Cell Phone for People who are Blind or Visually ImpairedMiniVision2+ - RAZ Mobility >> Next Generation Assistive Technology -
Box content
-
Getting started
-
Charging the battery
-
Turning the phone ON/OFF
-
Documents / Resources
-
References
-
Download manual
-
Contents
- 1 Overview
- 2 Box content
- 3 Getting started
- 4 Charging the battery
- 5 Turning the phone ON/OFF
- 6 Documents / Resources
- 6.1 References
- 6.2 Download manual
Kapsys MiniVision 2 - Phone Quick Starting Guide
Overview
- Flashlight
- Phone calls receiver
- Phone screen
- Control keys and navigation pad
Up: selects previous item Down: selects next item Left: decreases volume Right: increases volume Central « OK » button:
| |
Picks-up a call Activates a shortcut to access the « Phone » application | |
Hangs-up a call / Activates a shortcut to go back to the home screen A long press turns your MiniVision2 ON and OFF | |
Opens the menu associated with the current screen | |
Goes back to the previous screen / Deletes characters in an edit box |
- Alphanumeric keypad to input characters
- Microphone for phone calls and voice recognition
- 3.5 mm jack to connect provided earphones
- Micro USB connector to charge your MiniVision2
- Contact pads for docking station
- Camera
- SOS button
- Loudspeaker
Box content
MiniVision2 is delivered with:
- A battery
- A 220/110 Volts main charger – 5 Volts USB
- A Micro USB cable
- A pair of stereo earphones with microphone
- A docking station for charging
- A protective case
- A Quick starting guide
Getting started
Insert your SIM card and the provided battery
- Flip the phone over, place your fingernail in the notch located at the bottom left of the phone and lift the back cover up.
- The SIM connector is positioned at the top left corner of the electronic card, below the battery location. The internal label tells you its location. Put the SIM card into the compartment located on the right of the SIM connector, the chip should be pointing down and the cut corner placed at the bottom left. Push on the SIM card ightly with a tip of your finger and carefully slide it all the way to the left.
- Insert the battery placing the lower section first, with the connection pads at the bottom right, then put the front down into its location.
- Lastly, put the cover back, align its tabs with the adapted slots, and gently press the cover until it snaps in place.
Charging the battery
For initial use, it is recommended to charge the battery for at least four hours. After that, you can recharge the battery as needed.
Connect the USB cable between the MiniVision2 and the AC charger. Plug the AC charger into any AC outlet and charge the device. It is normal for a phone to heat-up when charging or during long periods of use.
You can also charge the MiniVision2 via the docking station. To do this, connect the USB cable between the docking station and the AC charger. Then connect the AC charger to AC outlet and place the MiniVision2 in its base. When the phone is on, a beep sounds to alert you that the phone is charging properly.
Note: the protective case is not compatible with the docking station.
Turning the phone ON/OFF
Turn ON your MiniVision2 with a long press on the hang-up key ().
MiniVision2 vibrates when you successfully turned it on. MiniVision2 is ready to use when the home screen is displayed.
When your MiniVision2 is ON, a short press of the hang-up key () puts it to standby mode (screen off), or back to running mode (screen on). The standby mode is activated after an inactive period for the battery to last.
In standby mode, the MiniVision2 screen is off but you can still receive incoming calls and messages. To turn MiniVision2 off, make a long press on the hang-up key (), then select "OK" and validate to confirm the shutdown. MiniVision2 vibrates when you successfully turned it off If the product does not turn on, check that the battery has been correctly installed and charged, if so, repeat the battery installation procedure.
Documents / Resources
References
Download manual
Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.
Download Kapsys MiniVision 2 - Phone Quick Starting Guide
Advertisem*nt
Do you have a question about the MiniVision 2 that isn't answered in the manual? Leave your question here.
Thank you! Your question has been received!
Save Article as PDF
Table of Contents
Delete from my manuals?
Click the green button to print the entire article.
To print the original version of the document - click the blue one.
Print document Print this article